The articles describes some wonderful experiments conducted by Mr.Steven, the images sent by him are just amazing and his work - pioneering, let's learn directly from Steven more about the developments....
"Today i successfully brewed and made my first colloidal silver using the latest circuits connected to the rf output of my sec exciter tower, despite already having my own built colloidal silver generator this is an experiment to find out what else you can do with the RF energy output of the sec exciter towers energy.
First i cleaned the brewing jay that has my 2 pure silver electrodes sticking through the lid then after drip drying out the washed brewing jar , i then filled it with the demineralised water ive always used for brewing colloidal silver before .Then i used the laser to shine through the jar of demineralised water , the laser beam can barely be seen so its not highlighted yet and there is no silver ions yet to high light the laser beam,
so then i linked to only one of the silver electrodes the red lead from the latest circuit , and the other silver electrode i left sitting and acting as an rf antenna , this can be checked by holding one leg of a neon light and then touching the other leg to the silver electrode , the neon will light up instantly so show some form of closed circiut going on here from one electrode to the other via either my body's capacitance of other energy cycle in the air whatever it is.
I let the brewing set for a while then hooked up the other wire from the last circuit to the other silver electrode with nothing hooked up to it i let that sit for a while then removed it so there's just one wire to one electrode and the other acting as the return rf energy wire .
I kept doing this for a little while then i used my laser to shine through the water , and the laser was starting to high light to indicate the presents of silver ions forming in the water and in the red beam you can see the microscopic particles of silver that the laser beam reflects off , also there was no bubbling at all on any of the electrodes , which is what you always get when brewing colloidal silver , there wasn't even a single finest bubble stream coming of the electrodes and going up , at all so whatever is going on is beyond the ability of the human eye to see it at all but it must be there i think the tiniest bubbles ever and every so often i remove the electrodes and give it a wipe and found light grey silver oxide on the clean white paper towel i used so there is a reaction going on and you cannot even see the grey oxide o the electrodes only when you wipe them off you can see it then on the towel.
I used a magnifying lens to look closely at the electrodes in the water while the invisible reaction was taking place and still not a single trace of even a vapor like trail was seen to be coming off the electrodes , and despite no grey oxide is visible on the electrodes it still shows up on the white paper towel the scan of the laser indicates its there and even the microscopic particles of silver can be seen for sure , after a time i then poured it out of the brewing jar then into a Pyrex jug and then into an amber colored bottle then i used the laser to do the Tyndall test and the laser was still high lighted and silver particles can be seen in the red laser beam . it looks like i have just as much silver and light amount of silver ions in the experimental brew".
"Hey swagatam if you've seen the circuit drawing ive emailed you here's the pictures of the real thing all built on printed circuit board with some upgrades to it . some of the details of what it dose is on the circuit drawing i just emailed you recently. still have some testing to do to see what else i can do with this .
I ran a test tonight using the latest circuit i sent you pictures of today, first i used whats left in a bottle of demineralsised water and put it into a jar, which i brew colloidal silver in, the lid of the jar has 2 pure silver electrodes, anyhow then i linked the rf active output lead of the circuit and other lead to the silver electrodes which was submerged under the demineralised water only a few inches.
anyhow i fired up the circuit, knowing pretty well that you use dc at low milliamps to make colloidal silver so anyhow im using rf currents and voltage. anyhow i let the circuit run just a short time and i then grabbed a neon globe and touched it to one of the electrodes. i had it in the alligator clip so i used it in that so by touching the one neon leg in the clip to the silver electrode while the other one was still connected , this formed a circuit and the neon would lite up to show conduction was occurring, then i used a lens to see if any bubbles was coming from the electrodes this would indicate the brew is going ok and soon, the production of silver ions would be noted , but there was no bubbles so i got my laser out and done a Tyndall test this is when you shine the laser through the colloidal silver to see if the laser beam is high-lighted that's bring up the beam to its bright red color to indicate the percents of silver ions in the water without the silver ions the laser would be hard to see and wouldn't then be high lighted.
anyhow to my surprise the beam was high lighted and in the red beam i can see the reflections of the tiny silver particles , so how could this be when its suposed to be done in dc and low current like 1 or a few milliamps and in such a short time , i have yet to re do this test as i dident wash the jar out before i did a test brew of colliodaal silver useing this possibly new method and even though the lid was on the jar im betting i may get the same results again , so when i get another bottle of diggers brand demineralised water here in western australia ill try the test again
Here's the pictures of the set up brewing colloidal silver using the sec exciter coil tower and joining circuits ive finished 2 successful bottles of colloidal silver light in silver ion taste and with the silver particles they are super anti biotic as they say they are and would be very beneficial in killing all kinds of bugs and bacteria in the body. pic the best pictures you like to use for your blog. help yourself.
hello swagatam, just emailing you to pass some time away, ive updated my wordpad document featuring all my notes research on the sec exciter experiments , you can edit it anyway you like and who knows a world wide sec handbook would be great then everyone on the net can contribute there knowledge and experiments on these and ideas just like in the j naudin web site they have a world lifters replication log so people making these aluminum foil and balsa wood lifters which levitate from the high voltage ion wind from wire to the foil can contribute to it . i be very interesting to know who looks at all the info and what there backgrounds are whether it be in engineering or nasa or some top people or scientists in the world for all we know , the internet is the information super highway , the next super highway of information comes from all the millions of great thinkers and minds who s ideas can be turned into something new by another person , or improved or made better .well time to email this don't want to hold you up mate look after yourself as you are very important to your the link that links new info to the internet so others can share and benefit from it for the good of science and discoveries and mankind.
Tonight measured the rf voltage output of my sec exciter tower , this was easy as you can hold a neon leg and touch the other to the single wire output of the sec exciter tower and it will light up it a 90 volts neon , anyhow i used my digital multimeter set to its highest ac range of 700 volts ac i ran the clip from the one terminal output of the sec exciter tower and held the other negative lead into the air to act as the rf voltage return and switched the driver circuit on at the very first instant i got a reading well past 1000 volts well past the 700 volts maximum of my meter then it dropped out as its to much but why the meter showed that highest reading past its 700 volts ac is unknown to me , i had the negative in the air but to close to the tower so i held it up thru the air, away and got a steady 748 volts ac then i moved the meter negative i was holding in the air to a spot just right and got a steady 778 volts ac that's 78 volts past the maximum meter setting in the ac range . im not gonna count it an an error nous reading as my meter works so well and it may have a few hidden surprises for all i know like they could read more than what they say they can i haven't videoed it but will do latter and i have gotten some weird results from other experiments that defy explanation .
My new method of brewing colloidal silver using the free energy generation of the sec exciter tower along with some circuits ive put together is generating some interest and curiosity , and the way i do it , looking forwards to the mass of viewers looking at the material when you put it up . while i can remember it ive got a test to do just to see if the brew holds any magnetism , this is done using the most sensitive magnetic field detector i can come up with that's a floating magnetized sewing needle floated on top of warm salty water in a drinking glass ive played with this detector before its so sensitive even the small voltage through the small battery operated torch makes the needle swing , glass of warm water let it settle then magnetize your sewing needle by rubbing both halves along the north and south pole of a magnet then place a small peace of tissue on top of the still warm salty water then place your needle on top of it the tissue will absorb the water and sink leaving the needle still floating"
In case i haven't emailed you these here's a newer circuit I'm experimenting with its a half captret circuit using one out of 2 photoflash capacitors top as an output on the Internet its called a captret im using 2 photo flash capacitors in it and one is configured as a captret so this is powered from my sec excitor series circuits.
I've brewed more colloidal silver using the energy from the sec exciter series coil tower and the sec exciter powered series circuits , and have been measuring the frequencies, my discovery of measuring the frequencies between the colloidal silver brew and the outside energy of the medium or other , ill explain how to tune it a bit or adjust the frequency, now first i attach the negative black lead of the frequency counter to one leg of the neon and i hold that lead in an alligator clip holder and bring bring it up to the colloidal silver brewing jar making sure its against the jar, the neon will glow lightly, then clip the red frequency counter lead to the one colloidal silver electrode where the single rf input goes to. so there will be one colloidal silver electrode left unused that's the rf antennae or return, the neon leg against the jar will be the second rf energy antennae. now once I've switched on my parallel transistor driver circuit on with the 9 volts 500 milliamps dc input reduced to 400 milliamps i switch the frequency counter on then allow it to stabilize then note the frequency. to alter the frequency just move the neon against the outside of the brewing jar up and down against the outside of the brewing jar watch the frequency hold at a single reading and after a time it will drop 7 or 6 frequencies for a time then gain it back again for mysterious reasons , also bringing your hand near the brewing jar will also change the frequencies as if it can sense your hand or bodies e field. all i need now is a few ufo sightings and hopefully ill be able to determine if the brew frequencies would change in accordance to the frequencies in the air by the ufos energy output , like power being induced into objects when ufos are nearby. ive done some more videos so far total 45 videos of the brewing of colloidal silver using the sec exciter's energy output .
"Today i successfully brewed and made my first colloidal silver using the latest circuits connected to the rf output of my sec exciter tower, despite already having my own built colloidal silver generator this is an experiment to find out what else you can do with the RF energy output of the sec exciter towers energy.
First i cleaned the brewing jay that has my 2 pure silver electrodes sticking through the lid then after drip drying out the washed brewing jar , i then filled it with the demineralised water ive always used for brewing colloidal silver before .Then i used the laser to shine through the jar of demineralised water , the laser beam can barely be seen so its not highlighted yet and there is no silver ions yet to high light the laser beam,
so then i linked to only one of the silver electrodes the red lead from the latest circuit , and the other silver electrode i left sitting and acting as an rf antenna , this can be checked by holding one leg of a neon light and then touching the other leg to the silver electrode , the neon will light up instantly so show some form of closed circiut going on here from one electrode to the other via either my body's capacitance of other energy cycle in the air whatever it is.
I let the brewing set for a while then hooked up the other wire from the last circuit to the other silver electrode with nothing hooked up to it i let that sit for a while then removed it so there's just one wire to one electrode and the other acting as the return rf energy wire .
I kept doing this for a little while then i used my laser to shine through the water , and the laser was starting to high light to indicate the presents of silver ions forming in the water and in the red beam you can see the microscopic particles of silver that the laser beam reflects off , also there was no bubbling at all on any of the electrodes , which is what you always get when brewing colloidal silver , there wasn't even a single finest bubble stream coming of the electrodes and going up , at all so whatever is going on is beyond the ability of the human eye to see it at all but it must be there i think the tiniest bubbles ever and every so often i remove the electrodes and give it a wipe and found light grey silver oxide on the clean white paper towel i used so there is a reaction going on and you cannot even see the grey oxide o the electrodes only when you wipe them off you can see it then on the towel.
I used a magnifying lens to look closely at the electrodes in the water while the invisible reaction was taking place and still not a single trace of even a vapor like trail was seen to be coming off the electrodes , and despite no grey oxide is visible on the electrodes it still shows up on the white paper towel the scan of the laser indicates its there and even the microscopic particles of silver can be seen for sure , after a time i then poured it out of the brewing jar then into a Pyrex jug and then into an amber colored bottle then i used the laser to do the Tyndall test and the laser was still high lighted and silver particles can be seen in the red laser beam . it looks like i have just as much silver and light amount of silver ions in the experimental brew".
"Hey swagatam if you've seen the circuit drawing ive emailed you here's the pictures of the real thing all built on printed circuit board with some upgrades to it . some of the details of what it dose is on the circuit drawing i just emailed you recently. still have some testing to do to see what else i can do with this .
I ran a test tonight using the latest circuit i sent you pictures of today, first i used whats left in a bottle of demineralsised water and put it into a jar, which i brew colloidal silver in, the lid of the jar has 2 pure silver electrodes, anyhow then i linked the rf active output lead of the circuit and other lead to the silver electrodes which was submerged under the demineralised water only a few inches.
anyhow i fired up the circuit, knowing pretty well that you use dc at low milliamps to make colloidal silver so anyhow im using rf currents and voltage. anyhow i let the circuit run just a short time and i then grabbed a neon globe and touched it to one of the electrodes. i had it in the alligator clip so i used it in that so by touching the one neon leg in the clip to the silver electrode while the other one was still connected , this formed a circuit and the neon would lite up to show conduction was occurring, then i used a lens to see if any bubbles was coming from the electrodes this would indicate the brew is going ok and soon, the production of silver ions would be noted , but there was no bubbles so i got my laser out and done a Tyndall test this is when you shine the laser through the colloidal silver to see if the laser beam is high-lighted that's bring up the beam to its bright red color to indicate the percents of silver ions in the water without the silver ions the laser would be hard to see and wouldn't then be high lighted.
anyhow to my surprise the beam was high lighted and in the red beam i can see the reflections of the tiny silver particles , so how could this be when its suposed to be done in dc and low current like 1 or a few milliamps and in such a short time , i have yet to re do this test as i dident wash the jar out before i did a test brew of colliodaal silver useing this possibly new method and even though the lid was on the jar im betting i may get the same results again , so when i get another bottle of diggers brand demineralised water here in western australia ill try the test again
Here's the pictures of the set up brewing colloidal silver using the sec exciter coil tower and joining circuits ive finished 2 successful bottles of colloidal silver light in silver ion taste and with the silver particles they are super anti biotic as they say they are and would be very beneficial in killing all kinds of bugs and bacteria in the body. pic the best pictures you like to use for your blog. help yourself.
Tonight measured the rf voltage output of my sec exciter tower , this was easy as you can hold a neon leg and touch the other to the single wire output of the sec exciter tower and it will light up it a 90 volts neon , anyhow i used my digital multimeter set to its highest ac range of 700 volts ac i ran the clip from the one terminal output of the sec exciter tower and held the other negative lead into the air to act as the rf voltage return and switched the driver circuit on at the very first instant i got a reading well past 1000 volts well past the 700 volts maximum of my meter then it dropped out as its to much but why the meter showed that highest reading past its 700 volts ac is unknown to me , i had the negative in the air but to close to the tower so i held it up thru the air, away and got a steady 748 volts ac then i moved the meter negative i was holding in the air to a spot just right and got a steady 778 volts ac that's 78 volts past the maximum meter setting in the ac range . im not gonna count it an an error nous reading as my meter works so well and it may have a few hidden surprises for all i know like they could read more than what they say they can i haven't videoed it but will do latter and i have gotten some weird results from other experiments that defy explanation .
My new method of brewing colloidal silver using the free energy generation of the sec exciter tower along with some circuits ive put together is generating some interest and curiosity , and the way i do it , looking forwards to the mass of viewers looking at the material when you put it up . while i can remember it ive got a test to do just to see if the brew holds any magnetism , this is done using the most sensitive magnetic field detector i can come up with that's a floating magnetized sewing needle floated on top of warm salty water in a drinking glass ive played with this detector before its so sensitive even the small voltage through the small battery operated torch makes the needle swing , glass of warm water let it settle then magnetize your sewing needle by rubbing both halves along the north and south pole of a magnet then place a small peace of tissue on top of the still warm salty water then place your needle on top of it the tissue will absorb the water and sink leaving the needle still floating"
COLLOIDAL SILVER BREWING UPDATES, USING THE SEC EXCITER AND SERIES CIRCUITS. July 22, 2012
IVE BEEN BREWING COLLOIDAL SILVER AGAIN FOR A FEW HOURS NOW AND IVE RIGGED MY FREQUENCY COUNTER TO THE BREWING JAR, USING A SIMILAR METHOD TO MEASURE THE BEST STEADY VOLTAGE READINGS FROM THE SILVER ELECTRODES, USING A NEON GLOBE, NOW FIRST I LINKED THE ACTIVE SINGLE WIRE RF VOLTAGE OUTPUT TO ONE OF THE 2 PURE SILVER ELECTRODES, THEN I RAN MY RED FREQUENCY COUNTER LEAD TO THE SAME SILVER ELECTRODE THAT THE SINGLE RF INPUT RUNS TO.
THEN I LINKED THE BLACK FREQUENCY COUNTER LEAD TO ONE LEG OF A NEON GLOBE AND THE OTHER LEG WAS HELD AGAIN THE OUTSIDE OF THE COLLOIDAL SILVER BREWING JAR THE NEON LIGHTS UP A LITTLE FROM THE ENERGY IN THE WATER OF THE JAR AND THE OTHER COLLOIDAL SILVER ELECTRODE IS LEFT UNUSED AS A ENERGY RETURN LIKE THE LEG OF THE NEON AGAINST THE OUTSIDE OF THE JAR, THE UNUSED SILVER ELECTRODE IS ACTIVE AND YOU CAN FEEL THE RF CHARGE FROM IT NOW WITH THIS SET UP THE FREQUENCY COUNTER READING IS A ROCK STEADY SINGLE FREQUENCY THAT HOLDS WELL FOR A TIME THEN JUMPS 6 FREQUENCIES THEN DROPS BACK LIKE IT WAS STABILIZING ITSELF , SO ANYTHING ELSE IN THE SEA OF ENERGY THAT MAY INTERACT WITH IT TO CAUSE A FREQUENCY DROP WOULD END UP MYSTERIOUSLY CORRECTING ITSELF THEN JUMP BACK TO ITS STEADY FREQUENCY READING . OUT OF 4 LOTS OF COLLOIDAL SILVER BREWING IVE HAD SIMILAR RESULTS SO WHATEVER THE EXTRA FREQUENCY'S ARE THAT MAY INTERACT WITH THE FREQUENCIES OF THE BREW SUDDENLY CHANGE IT FOR A SHORT TIME THEN IT GOES BACK TO ITS STEADY FREQUENCY READING. IVE SHOT A NUMBER OF VIDEOS AND SO HAVE TO REVIEW THEM ALL AND I WAS LUCKY TO CAPTURE THE BIGGEST OR MYSTERIOUS FREQUENCY CHANGE BEFORE IT WENT BACK TO WHERE IT WAS, ON CAMERA SO IT’S A MYSTERY, FOR ALL I CAN GUESS THE FREQUENCY OF ENERGY OF A UFO COULD BE CAUSING THESE MYSTERY FREQUENCY CHANGES TO MY SET UP MY BREWING COULD BE ACTING LIKE A ENERGY FREQUENCY DETECTOR OF SOME KIND FOR ALL I CAN GUESS, ILL INVESTIGATE SOME MORE.In case i haven't emailed you these here's a newer circuit I'm experimenting with its a half captret circuit using one out of 2 photoflash capacitors top as an output on the Internet its called a captret im using 2 photo flash capacitors in it and one is configured as a captret so this is powered from my sec excitor series circuits.
0 Response to "How to Make Colloidal Silver at Home - By Steven Chiverton"
Posting Komentar